Guidelines to Install a Rough Plumbing System – From The Top Plumber In Phoenix
A rough-in method is the process of laying out the tools to use in installing a plumbing system in the house or of any establishments. This is usually done while the building is still being constructed. It is the perfect time to install the pipelines on the floors, walls or underground locations.
You can actually do it yourself without paying for anyone. Here are the guidelines in order to install your plumbing systems by yourself.
Installation of Rough Plumbing in the Drainage System
The drainage system is one of the few kinds of plumbing system and needs a proper installation. These are the guidelines that should help you do it on your own.
Create a blueprint of the drainage system that you are planning to install. The draft should show all the pipes, angles, valves and drainage supplies that has to be used and on where each of it will be placed.
If you have trouble drafting the plan, you can always seek for assistance from our plumber Phoenix team.
Use a fixing glue or pipe cement to connect the pipes together. There’s an applicator brush that comes with the glue package to apply it at both ends of the pipe supplies that are going to be connected together.
After doing so, connect the pipelines and make sure that they are all perfectly sealed. After connecting them, slowly twist to be able to spread the glue and seal it more.
Our best plumber in Phoenix team carefully does this procedure to make sure that there will be no leaks in the water drains.
To install a plumbing system in the shower and sink areas, there’s a need to use a 2 inch pipe. Use a 3 inch pipe in installing the system in the major lines like the ones in the bathroom and the kitchen.
The pipelines should be vented in a vertical form that could pass through the roof or the wall.
Our 24 hour plumber Phoenix team follows the same concept in installing drainages.
Purchase studs from local plumber stores and notch it on the line of the drainages. Next, cover the opening and the end of the notch using a metal material. It will prevent screws, nails and too much heating from damaging the pipelines.
Lastly, make use of a plumbing service tape to make the drain lines hanging all of the time. There is a required slope measurement in drain lines. Make sure that the right measurement is being followed during the installation.
If anything goes wrong with your installation, our emergency plumber Phoenix team is always ready to serve.
Installation of Rough Plumbing in Water Systems
This is the system that is often associated with faucet repair and drain repair that are usually being taken care of by our plumber in Phoenix contractor team.
You also need to create the draft plan of this system that illustrates all the angles and the sizes of the different plumbing tools to use. It would be easier to install if there is a draft to be followed. You can always ask for assistance from our plumber Phoenix team to help you in illustrating your plan.
Creating a diagram beforehand will save you time and effort from going back and forth to the hardware stores if the tools are not enough.
Our best plumber in Phoenix team has specific pipe sizes to use.
¾ inch pipe – use this size for the main lines like the ones that passes the bathroom, kitchen and many others.
½ inch pipe – this size is to be used on branch and individual lines.
“L” and “M” – these are to be used for installing copper plumbing systems
Schedule 40 – this is the pipe type that is commonly used on plastic plumbing systems.
These are the standard measurements that our emergency plumber Phoenix team follows.
Use a soldering gun in to connect copper pipelines and make sure that the tools are cleaned perfectly. Also, use a torch or real heat in order to spread the flux within the entire connection area. Wait for the flux to bubble due to heat. Once it’s properly heated, remove the fire or heat and start soldering it together.
There should be drilled holes within the studs and make sure that these holes are a little bit larger than the pipelines that are going to be installed.
Start securing the fixtures that will be attached into the walls by simply using a plumber‘s tape.
The installation of the two systems has similar procedures, but has a few differences. It’s not hard to differentiate though, but for easier and hassle-less installation you can always ask for plumbing companies to do it for you.
Our company offers the lowest plumbing repair costs of plumbing services and we always aim to produce excellent results.
Mr. Speedy Plumbing
Address:
Phoenix, AZ
Phone:
(800)-207-1548
View Map
Phoenix Plumbing Services:
- Faucet Replacement and Repair
- Commercial Plumbing Services
- Drain Cleaning Service
- Electronic Leak Detection
- Water Heater Installations
Hours of Operation
- Monday 7:00 am – 10:00 pm
- Tuesday 7:00 am – 10:00 pm
- Wednesday 7:00 am – 10:00 pm
- Thursday 7:00 am – 10:00 pm
- Friday 7:00 am – 10:00 pm
- Saturday 7:00 am – 10:00 pm
- Sunday 7:00 am – 10:00 pm